Author Topic: My Beta restoration  (Read 63485 times)

0 Members and 4 Guests are viewing this topic.

Offline Carlwil10

  • Jr. Member
  • **
  • Posts: 49
  • Country: gb
Re: My Beta restoration
« Reply #60 on: September 09, 2026, 05:47:11 PM »
No worries Guy, I think I'll  be cutting those little bits out anyway to get behind them

Offline deks

  • Hero Member
  • *****
  • Posts: 313
  • Country: gb
  • Steve Hudson
Re: My Beta restoration
« Reply #61 on: September 09, 2026, 06:26:01 PM »
Some big bits missing there Carl. Are you replacing the vertical part of the inner wing? Or fabricating it?

Apologies, still got a bad back so I haven't had a chance to photograph the underside of my car for comparison!

How similar is the Spyder front end as Mine is on its side and easy to photo. I will in time be cutting the front end off to sell when/if some needs bits. Ive just got to work out where I either unstitching or cutting it. Reminds me best invest in some new spot weld drill bits mine are years old and probably blunt
Lancia Beta Spyder 2000 (1979 model)
Lancia Beta HPE 2000 IE (1983)

Offline peteracs

  • Administrator
  • Legendary Member
  • *****
  • Posts: 5031
  • Country: gb
  • Peter Stokes
Re: My Beta restoration
« Reply #62 on: September 09, 2026, 09:15:54 PM »
Hi

The Spider front end is the same as the Coupe,, though Carl's is a pre facelift, so maybe the odd small difference.

Peter
Beta Spyder S2 pre F/L 1600
Beta HPE S2 pre F/L 1600

Offline Carlwil10

  • Jr. Member
  • **
  • Posts: 49
  • Country: gb
Re: My Beta restoration
« Reply #63 on: September 10, 2026, 07:13:59 AM »
I noticed that this area on Guys car is different to mine. It may have been changed at the factory as on mine there's an area that cant be treated and would get dirt build up behind it. I'll be cutting it off to clean it all up and treat.

Carl

Offline peteracs

  • Administrator
  • Legendary Member
  • *****
  • Posts: 5031
  • Country: gb
  • Peter Stokes
Re: My Beta restoration
« Reply #64 on: September 10, 2026, 07:53:14 AM »
Hi Carl

Also Guy's car will have plastic wing liners, yours originally did not, though it may be possible to retrofit them.

I have a spare set if you want to give it a go.

Peter
Beta Spyder S2 pre F/L 1600
Beta HPE S2 pre F/L 1600

Offline Carlwil10

  • Jr. Member
  • **
  • Posts: 49
  • Country: gb
Re: My Beta restoration
« Reply #65 on: September 10, 2026, 10:25:37 PM »
Hi peter

Yes thanks I'll have and see if I can get them to fit thanks

Carl

Offline SanRemo78

  • Legendary Member
  • ******
  • Posts: 1627
Hawk HF3000 - Square Arch Stratos Replica - owned since 1988.
Skoda Superb Scout 2021. Believed 1of 1 in the UK!
Fiat Panda 100HP and now -
A Lancia Beta Coupe 1981 2 Litre

Offline Carlwil10

  • Jr. Member
  • **
  • Posts: 49
  • Country: gb
Re: My Beta restoration
« Reply #67 on: September 21, 2026, 01:48:37 AM »
Thanks guy, that's the same as yours so I think I'll cut my section out.

Carl

Offline Carlwil10

  • Jr. Member
  • **
  • Posts: 49
  • Country: gb
Re: My Beta restoration
« Reply #68 on: October 04, 2026, 04:31:10 PM »
A bit more progress on my coupe. The first bit of epoxy primer on. Now what's people's thoughts on using rivnuts along the top to bolt the wings on.

Carl

Offline SanRemo78

  • Legendary Member
  • ******
  • Posts: 1627
Re: My Beta restoration
« Reply #69 on: October 04, 2026, 05:36:26 PM »
That's what I've used Carl!
Hawk HF3000 - Square Arch Stratos Replica - owned since 1988.
Skoda Superb Scout 2021. Believed 1of 1 in the UK!
Fiat Panda 100HP and now -
A Lancia Beta Coupe 1981 2 Litre

Offline Carlwil10

  • Jr. Member
  • **
  • Posts: 49
  • Country: gb
Re: My Beta restoration
« Reply #70 on: October 04, 2026, 06:48:56 PM »
Ok Guy, I'll go with them then

Carl

Offline Ferrit

  • Legendary Member
  • ******
  • Posts: 1058
  • Country: gb
  • Mark Ferris
Re: My Beta restoration
« Reply #71 on: October 04, 2026, 10:15:41 PM »
That sounds like a win! :-)
Lancia Beta Coupe 2000 SA import, now project
VW Caravelle t5.1 was project
Pig 3008 EV

Offline Niko

  • Newbie
  • *
  • Posts: 9
  • Country: be
Re: My Beta restoration
« Reply #72 on: October 27, 2026, 04:47:23 PM »
Carl, thank you to have been revived my Beta interest and filled my wish to follow a Beta restoration channel on YT.
The occasion was presented to me to buy one again and reignited the covered fire.
I really like to watch your progresses as i wish to start the restoration of my own car and put in it some of my vision of this great drivers car.

My 2cts is to go for a 1800 or 2000 engine WITH power steering and 4 carburetors in place of the single double one.

Wish you good work, we need brave (YT videos) and skilled man like YOU to get this wonderful car out of the shadow.

PS: There is some advantages to this shadow, but at the end, the most important is the put them back on the road, after intensive rust repair and protection to finally get the pleasure to drive it again.

Offline Carlwil10

  • Jr. Member
  • **
  • Posts: 49
  • Country: gb
Re: My Beta restoration
« Reply #73 on: October 31, 2026, 03:04:45 PM »
Thank you Niko, glad you are enjoying the videos. Good luck with your search for a car.

Carl

Offline Carlwil10

  • Jr. Member
  • **
  • Posts: 49
  • Country: gb
Re: My Beta restoration
« Reply #74 on: November 18, 2026, 01:58:32 AM »
My drivers side inner wing looks like it could be fun 😁

Offline peteracs

  • Administrator
  • Legendary Member
  • *****
  • Posts: 5031
  • Country: gb
  • Peter Stokes
Re: My Beta restoration
« Reply #75 on: November 18, 2026, 08:36:20 AM »
My drivers side inner wing looks like it could be fun 😁

Hi Carl

A bit of a mess with crap repairs to boot. Reminds me of my Spider without the repairs.

Best of luck with it.

Peter
Beta Spyder S2 pre F/L 1600
Beta HPE S2 pre F/L 1600

Offline WestonE

  • Legendary Member
  • ******
  • Posts: 2050
  • Country: gb
Re: My Beta restoration
« Reply #76 on: November 18, 2026, 08:53:47 AM »
You might be better getting a decent cut off front end from an IE or VX (better rust proofing) and cutting out the right large section to use.

Offline Ferrit

  • Legendary Member
  • ******
  • Posts: 1058
  • Country: gb
  • Mark Ferris
Re: My Beta restoration
« Reply #77 on: November 18, 2026, 09:48:27 AM »
Holee crap!  Thats not good.  A bit of a head scratch to where do you start?  Do you have a plan?
Lancia Beta Coupe 2000 SA import, now project
VW Caravelle t5.1 was project
Pig 3008 EV

Offline SanRemo78

  • Legendary Member
  • ******
  • Posts: 1627
Re: My Beta restoration
« Reply #78 on: November 18, 2026, 02:59:26 PM »
Mmmm - extra crispy...

Perhaps this might help?
https://www.ebay.it/itm/116362464999?_skw=lancia+beta&itmmeta=01M7QJEQ5VYX74ERYS01MWZH52&hash=item1b17be4ee7:g:gL4AAOSwtKhnEjHi

Mark may also have this panel and the vertical part/top box section?

Guy
Hawk HF3000 - Square Arch Stratos Replica - owned since 1988.
Skoda Superb Scout 2021. Believed 1of 1 in the UK!
Fiat Panda 100HP and now -
A Lancia Beta Coupe 1981 2 Litre

Offline Carlwil10

  • Jr. Member
  • **
  • Posts: 49
  • Country: gb
Re: My Beta restoration
« Reply #79 on: November 18, 2026, 03:27:51 PM »
I will be fabricating it all so its new metal, it'll be a good challenge and part of the experience I wanted. 😆😁. Hopefully it'll make a good episode.